TAG: Powerflushing

01305 786036

Powerflushing and Central Heating Circulation Problems

The Need To Powerflush Your System

Sludge and debris if left in heating systems will accumulate in the boiler and radiators, dramatically reducing their effectiveness and will eventually lead to a loss of efficiency or premature failure of the appliance.

 

The following are some of the problems that could be avoided with a Powerflush as it removes the Magnetite sludge from your system :

 

  • Cold radiators or cold spots on radiators
  • Excessive noise from the boiler or pump possible leading to premature failure
  • Heating pump circulation problems
  • Pipe blockages
  • Internal corrosion
  • System blockages
  • Discoloured water when you bleed a radiator or in severe cases when you run a tap
  • Poor or even non existant hot water even when the system has been running a while
  •  

These problems on their own may be able to be rectified without Powerflushing, however if you notice more than one sign then its probably worth considering a powerflush.

The benefits of power flushing

The result of power flushing is that the boiler and the rest of the central heating system become more efficient. This occurs because there is better circulation through the pipework and radiators and in turn the boiler doesn't have to work so hard to warm the house and water, Therefore the overall result is that you will save money on your heating bills.

 

Consequences of not power flushing

If your heating system does need to be power flushed and you decide not to do it then the problems will almost certainly get worse. The circulation through the pipes and the radiators will slow until very little hot water gets through. This means that the house will not heat up and the boiler will be working harder and be working for no real reason. The result of this is that energy will be wasted and in the long run money will be wasted as well.

New Boilers

In accordance with BS7593, boiler manufacturers requirements and benchmark. All new replacement boilers installed on to existing heating systems and new heating systems should be power flushed to ensure all sludge, Magnetite, fluxes, residues, excess jointing compound, mineral oils and other contaminants are thoroughly flushed from the system to ensure peak performance of the boiler and heating system

How do we do a power flush

When power flushing, we as a company use both the Powerflush and Magnetite machines, connecting them to the heating system. The principle is to create a powerful fresh water flow under controlled conditions to remove the debris from the system. After connecting the Powerflush and Magnetite cleaning machines to the heating systems, a chemical cleaner is added to the system.

 

The contaminated water passes through the system which removes the circulating black iron oxide contamination from the flushing water quickly and simply using the power of a large magnet which attracts the magnetic iron oxide away from the water flow. The rapid removal of debris from the flushing water prevents saturation of the chemical cleaner solution with the black sludge, leading to a more effective power flush.

 

When the new boiler/heating system has been installed and before the final commissioning of the boiler we again carry out a manual flush of the system adding a pre- commission cleaning agent. The water is circulated around the system breaking down any flux's, jointing agent etc that might have been introduced into the system, in to suspended parts making it easier to flush out the system. The system is once again drained, re-filled with fresh water and an inhibitor added. The inhibitor helps to protect the system from within, stopping the build up of sludge within the system, ensuring maximum efficiency and minimum fuel usage.

 

 

So is power flushing worth it? The answer to this depends on how affected your heating system is. If the entire system is showing signs of bad circulation or you notice more than two of the signs mentioned above then a powerflush will probably be worth the money you pay.

 

For more information on powerflushing or advice on whether you need a powerflush then call us today

12 Albany Road, Granby Ind Est. Weymouth, Dorset, DT4 9TH

Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester
Gas Safe Registered Installers at Earley and Lock Weymouth and Dorchester